Peterson on Fire Logs offers the best solutions available to enhance your fireplace with their vented gas logs. They not only provide the feel and look of a conventional wood burning fire, but much better safety and ease of operation. Here is our step-by-step installation guide to help install your Peterson Vented Logs safely and efficiently. Following these instructions will also maximize the useful life and performance of the fireplace system.
Preparing Your Fireplace for Installation
Before installing your Peterson Vented Logs, proper preparation of the fireplace is required for safe and efficient operation of your logs.
- Proper Cleaning of the Fireplace
- Clean out ash and debris: The fireplace should be free of residual ash, soot, or any other remains from fires gone by.
- Look for any obstruction: Obstruction of any kind in the chimney or the venting system impedes flow and creates hazardous conditions.
- Vacuum and wipe surfaces: Dust off the firebox and surrounding areas to prevent buildup that could affect the flame.
- Ensure Proper Venting
- Chimney and damper checked: That may mean simply the chimney is open, but more importantly, the damper needs to be cleaned and should allow proper airflow.
- Flue system: The flue must be in good working order as the venting system provides a critical path to safely vent combustion gasses.
- Know when to call in a professional: If you aren't confident about your venting system, it is a good idea to have a professional chimney sweep inspect it.
- Verify Gas Line Readiness
- Gas supply: Make sure the gas supply is off before commencing with the installation to avoid accidents.
- Damage/Gas Line Inspection: The gas line should be checked for cracks, leaks, or damage to avoid dangerous gas leaks at installation.
Installation Instructions for Peterson Vented Logs
Now, with your fireplace prepared for a proper installation, Peterson Vented Logs can be installed. From here, very closely follow the manufacturer's instructions for the safest and most effective installation process.
- Position the Burner Correctly
- Place the burner system: The burner is the heart of the log system, and it must be snugly positioned right in the middle of the firebox area.
- Alignment check: The burner should be aligned correctly to ensure the proper distribution of the flame and to save on gas.
- Anchor the burner: Install the burner according to the manufacturer's instructions, securing it appropriately to the bottom of the fireplace so it does not shift during operation.
- Stack the Logs
- Log placement instruction: Peterson on Fire Logs gives explicit information on the appropriate way to place the logs. Closely following the instructions will not only give good-looking results but also functional satisfaction.
- Allow for good airflow: Make sure logs are set apart to ensure good airflow and an even flame.
- Ceramic materials used: Peterson logs are made from advanced ceramic materials that can handle very high temperatures; this provides longevity and the realism of the flame.
- Safely Connect the Gas Line
- Ensure good connection: The gas line should be properly connected as instructed in the manufacturer's document. This is important both for the safety as well as for the proper performance of your system.
- Correct fittings: Make sure you are using the correct fittings and connectors according to Peterson's guide. Improper fittings lead to gas leaks.
- Leak test: Once the gas line is attached, check the line by using a gas leak detector or soapy water before continuing with the following steps.
Post-Installation Safety Tips
Safety post installation A few post-installation safety factors should be followed after Peterson on Fire Logs are installed. This is to ensure your set functions safely for many years to come.
- Check the Setup for Leaks
- Soapy water: After the gas has been turned on, use soapy water on the connections. If there are bubbles, there's a leak.
- Shut Off the Gas Immediately: If you suspect any leak by smell, then turn off the supply of gas and call a professional to check and remedy the issue.
- Fittings and connections: The fittings must be firm, and there must not be any loose fittings in the gas line.
- Ensure Proper Ventilation
- Open the chimney damper fully: This is important to let all smoke and gas exit safely, preventing the accumulation of dangerous gases in your house.
- Monitor airflow: Allow for an appropriate ventilation of the room, so that there is enough air passing through the chimney and the room.
- Install carbon monoxide detectors: It is wise to install carbon monoxide detectors near the fireplace against the chance that some toxic gas leak goes undetected.
- Fire the Logs Test
- First firing of logs: Once you are assured of no leakages, ignite the logs. Light up in low flame and build it up according to your requirements.
- Flame behavior: Check whether the flame is burning precisely. If the flame is too tall or too low, then adjust it with the help of a user manual.
- Observe the system operating: Let the fire burn for at least 15 minutes to ensure all is operating as expected.
Final Considerations
Peterson Vented Logs are known for their reliability and the cozy warmth they can add to a home. To ensure long life for your logs, maintenance will be necessary. After your log set has been installed, note the operation of the burner system and the logs. Occasionally clean your fireplace, and always ensure your venting system is working correctly.
If there is any problem, it will always be advisable to consult a professional or follow the troubleshooting advice from the manufacturer's guide.
Conclusion
The installation of Peterson on Fire Logs is fairly simple and can alter the appearance and sensation in one's fireplace. If one adheres to this manual, then Peterson on Fire Logs will be installed safely and effectively for long-term warmth and ambiance. Remember to have periodic checks on the system for leaks and proper ventilation so it will work safely.
For further enhancements to your fireplace, read our next article: Enhance Your Fireplace with Peterson Burner Systems.
